Acetyl乙酰

Acid-proof paint耐酸涂料, 耐酸油漆

Acrylic fiber丙烯酸纖維

Acrylic resin丙烯酸樹脂

Active filler活性填料

Adapter assembly接頭組件

Addition polyimide加成型聚酰亞胺

Addition polymer加聚物

Adjusting valve調整閥，調節閥

Adhesion assembly粘合裝配

Adhesion bond膠結

Adjustable-bed press工作臺可調式壓力機

Adjuster shim調整墊片

Adjusting accuracy調整精度，調校精度

Admissible error容許誤差

Admissible load容許載荷

Adsorbed layer吸附層

Advanced composite material先進復合材料，高級復合材料

Advanced development vehicle試制車，預研樣車

AE(Automobile Engineering)汽車工程技術

Aeolotropic material各向異性材料

Aerated plastics泡沫塑料, 多孔塑料

Aerodynamic body流線型車身

Aft cross member底盤/車架后橫梁

Air bleeder排氣孔

Air clamp氣動夾具

Air deflector導流板；導風板，氣流偏轉板

Air intake manifold進氣歧管

Air servo伺服氣泵

Air-tight joint氣密接頭

All-plastic molded全塑模注的

All polyester seat全聚酯座椅

Alligatoring龜裂，涂膜皺皮,表面裂痕

Amino resin氨基樹脂

Angular test撓曲試驗

Anti-chipping primer抗破裂底漆（底層涂料）

Apron防護擋板

Aramid fibre composites芳胺纖維復合材料

Assembly drawing裝配圖

Assembly jig裝配夾具

Assembly part裝配件，組合件

Autoclave forming熱壓罐成型

Autocorrection自動校正

Automatic compensation自動補償

Automatic feed自動進料

Automobile instrument汽車儀表板

Automotive transmission汽車傳動裝置，汽車變速器

Auxiliary fascia console副儀表板

Axial strain軸向應變

Axle bushing軸襯

Axle fairing底盤車橋整流罩

A Stage A 階段(某些熱固性樹脂聚合作用的初期階段)

AAC(Auxiliary Air Control)輔助空氣控制

ABC(Active Body Control)主動式車身控制裝置

Adherent阻粘劑

Ability meter測力計，性能測試儀

ABL (Ablative)燒蝕劑

Ablation燒蝕

Ablative composite material燒蝕復合材料

Ablative insulative material燒蝕絕熱材料

Ablative polymer燒蝕聚合物

Ablative prepreg燒蝕性預浸料

Ablative resistance耐燒蝕性

ABR (Acrylate Butadience Rubber)丙烯酸丁二烯橡膠

Abradant material研磨材料，磨料

Abrade研磨；用噴砂清理

Abrasion磨耗

Abrasion coefficient磨耗系數

Abrasion loss磨耗量，磨損量

Abrasion performance磨耗性

Abrasion-proof material耐磨材料

Abrasion resistant paint耐磨涂料

Abrasion test磨損試驗

Abrasive blast system噴砂清理系統

Abrasive cloth砂布

Abrasive disc砂輪盤，砂輪片

Abrasive finishing拋光

Abrasive paper砂紙

Abrasive resistance耐磨性

ABS(Acrylonitrile Butadiene Styrene) resin ABS樹脂，丙烯腈-丁二烯-苯乙烯(熱塑性)樹脂

ABSM(American Bureau of Standard Materials)美國標準材料局

Absolute dynamic modulus絕對動態模量

Absolute error絕對誤差

Absorbent material吸收性材料,吸收性物質，吸聲材料，吸收劑

Absorber減振器，阻尼器，緩沖器

ACA(Automotive Composite Alliance)汽車復合材料協會

ACC(Automatic Clutch Control)自動離合器操縱控制

Accelerant促進劑，加速劑

Accelerated aging test加速老化試驗，人工老化試驗

Accelerator pedal shaft加速踏板軸

Accelerator pump nozzle加速泵噴嘴

Acceptable life有效使用壽命

Acceptance test specification驗收測試規范

Access panel罩板,蓋板

Accessory配件，附屬品

Accessory equipment輔助設備

Accessory kit附件包，成套附件

Accumulator can儲電池外殼

Accumulator package蓄壓器組件，蓄壓器單元

Accuracy in calibration校準精度

Accuracy of finish最終加工精度

Accuracy of manufacture制造精度

Accuracy of positioning定位精度

Accuracy of repetition重現精度，復制精度

Acetal matrix composites縮醛樹脂基復合材料

Acetal plastic縮醛塑料,聚甲醛塑料

Acetal resin縮醛樹脂

Acetamide乙酰胺

Acetate fiber醋酸纖維，乙酸纖維

Acetone丙酮

Back corner panel后圍角板

Back panel后圍板

Back side panel后側板

Back wall pillar后圍立柱

Backer襯料

Baffler擋板，阻尼器；導流葉片

Bag Molding氣囊施壓成型(袋模法)

Baggage holder行李架

Barrier coat阻擋層；防滲涂層

Batch mixing分批混合，批混

Batching unit分批加料裝置

Bearing assembly軸承組合件

Biaxial winding雙角纏繞, 雙軸纏繞

Binder fiber粘合纖維

Bipolymer二元共聚物

Bismaleimide composites雙馬來酰亞胺復合材料

Blank placement坯料的放置

Blanket玻璃纖維氈；坯料

Blanking press沖壓機, 沖割壓力機

Blending resin摻合樹脂

BMC(Bulk Moulding Compound)團狀膜塑料

BMI (Bismaleimide)雙馬來酰亞胺

Body back panel車身后板

Body back wall車身駕駛室后圍

Body bracket車身支架

Body control module車身控制模塊

Body frame (Body skeleton)車身骨架

Body front panel車身駕駛室前圍板

Body monocoque單殼體車身，單殼式結構車身

Body outer panel駕駛室覆蓋件；駕駛室覆蓋件

Body structural member車身結構件

Body trim車身裝飾件

Bonded riveted structure膠鉚結構

Bonnet發動機罩

Brake制動器

Brake arrangement制動裝置

Brinell hardness test布氏硬度試驗

Brittle coating脆性涂層

Bulk coat整體涂層

Bulk heat treatment整體熱處理

Bulk moulding compound(增強塑料)預制整體模塑料

Bumper bracket(holder)保險杠托架

Bus brake system客車制動系

Butt flange對接法蘭

Butt joint對接接頭；對接

Butterfly valve節流閥，節氣門

BWI (Body In White)白車身

Cab deflector shield駕駛室導流板

Cab fairing駕駛室整流罩

Cab floor駕駛室地板

Cab mounting駕駛室懸置

CAD(Computer Aided Design)計算機輔助設計

CAE (Computer Aided Engineering)計算機輔助工程設計

Calibration tolerance校準公差

Calibrating instrument校準儀表

Camouflage paint覆面漆, 蓋面涂料, 偽假漆

Cantilever beam impact test懸臂梁沖擊試驗

Carbon-felt reinforced carbon composites碳?xì)衷鰪?qiáng)碳復合材料

Carbon fiber clutch碳纖維離合器

Carbon filament cloth碳絲織物

Case extension外殼的伸出部分，延伸外殼

Casing gasket外殼密封墊

Catalyst manifold固化劑總成

Catalyst pump固化劑泵

Catalyst ratio固化劑比率

Cavity模槽，型腔；凹模

Cavity block陰模

Cavity depth模槽深度

Cellular board蜂窩狀板，多孔板

Cellular plastics泡沫塑料，多孔塑料

Centre boss輪轂

Centre pin銷軸，樞軸，主銷

Centrifugal casting moulding離心澆鑄成型

Centrosymmetry中心對稱層板

Ceramic matrix composites陶瓷基復合材料

Charge填充氣體，填充料

Chasis底盤；機殼，車架

Chlorinated polyethlene聚氯乙烯

Chopped fiber短切纖維

Chopped random mat短切無序氈

Chopped strand短切原絲

CIRTM(Co-Injection RTM)共注射RTM

Clamping fixture夾具，夾緊裝置

Clamping force夾持力，合模力

Class A surface  A級表面

Clear coat透明涂層，透明罩漆，清漆層

Clear coat finish清漆涂層

Clicker die沖模

Climb milling同向銑削, 順銑

Clipping press切邊壓力機

Closure pressing speed合模速度

CMM(Closed Mould Moulding)閉合模塑

CMT(Compression Molding擠壓成型工藝

CNC(Computerized Numerical Control）電腦數值控制

Coarse grinding粗磨，用砂輪初加工

Coating defect涂層缺陷

Collision test碰撞試驗，撞車試驗

Combination property綜合性能

Concept design概念設計

Convection modulus對流模量

Convergence test收斂試驗

Cooling fixture冷卻夾具

Cooling tower冷卻塔

Crazing龜裂，細裂紋

Cresol resin甲酚樹脂

Cutting felt氈的剪切

Cutting-off bushing環形下料模; 下料環

Damped structure阻尼緩沖結構

Damper bracket件振器支架

Dashboard illumination儀表板照明

Dash trimming前圍板襯板

Deburring去毛刺，倒角，除飛邊

Deep drawing forming深拉成型

Deflection test撓曲試驗

Dent resistance耐沖擊性

Design freedom設計自由度

Detail drawing祥圖，零件圖

Die assembly壓模裝置

Die casting壓模鑄件,壓模鑄法

Dimethyl fomamide二甲基甲酰胺

Dimethyl ketone二甲基甲酮; 丙酮

Dip pretreatment浸漬預處理

Die prime coat浸漬打底漆

Dimensional stability尺寸穩定性

Dip coating浸涂

Dip forming浸漬成型

Durability testing耐久性試驗，壽命試驗

Dwell保壓,暫停加壓；滯留時間

Dynamometer測力計

Edge effect邊緣效應，邊界效應

Edge feed邊緣進料

Edge gate側澆口

Ejection force脫模力

Ejector起模桿

Ejector guide pillar推板導套

Ejector housing支架

Elasticizer增塑劑

Elastomeric composites高彈體復合材料

Elongation at break斷裂延伸率

Energy absorbing foam吸能泡沫塑料

Epoxy resin環氧樹脂

Ether ketone酮醚

Explosion proof防爆

Exterior body paneling車身外板部蒙皮

Exterior trim外飾，外飾件

Fabric composites織物復合材料

Fabric impregnation織物浸漬

Fabric preform織物預成型

Fabric prereg織物預浸料

Fabrication parameter制造參數

Fabrication procedure制造工序

Fabricating machinery加工設備

Face plate coupling法蘭式連接

Factory primer工廠底漆，工廠防銹漆

Fairing整流罩，整流裝置

Fairing panel前裙板

Fascia bracket儀表板支架

Fascia mask儀表板罩板

Fastening clamp夾緊裝置，緊固夾子

Fatigue tension test拉伸疲勞性試驗

FCM(Fibrous Composite material)纖維復合材料

FEA(Finite Element Analysis)有限元分析

Feed system供料系統

Feeding pump供給泵

Feeding speed進給速度

Female groove凹模

Female mould(tooling)陰模

Fender翼子板；護板

Fender apron擋泥板

Fender inner panel翼子板內襯護板

Fiber composite laminate纖維復合材料層板

Fiber mat layer纖維氈層

Finisher(Finishing component)裝飾件

Flange法蘭, 凸緣

Flange fitting法蘭式管接頭

Flash毛邊

Flash mold毛邊模具

Front sheet metal車前板制件

Fuselage fairing機身整流裝置

Gage kit儀表組，儀表套件

Gas cavity氣泡，砂眼

Gauge panel儀表板

Gear assembly齒輪傳動裝置, 減速器

Gearbox cover變速器殼蓋

Gear bracket support齒輪托支架

Gel coat膠衣,凝膠涂層

Gel coat drum膠衣圓桶

Gel coat flow monitor膠衣流量監控器

Gel time凝膠時間

Glass fiber winding machine玻璃纖維纏繞機

Glass wool玻璃棉

Glass yarn玻璃絲

Guiding device導向裝置

Gunk預混料

Gusset角撐件

Gutter channel流水槽

Hand lay-up 手工鋪疊，手工鋪貼

Hardness testing machine硬度測試儀

Hauling truck拖車

Header board outside panel前板外板

Headrest靠枕

Heat barrier material隔熱材料

Heat forming熱成型

High molecular material高分子材料

High pressure bag molding高壓袋成型工藝

High pressure injection moulding高壓注射成型，高壓注射模塑

High-strength structural adhesives高強度結構粘合劑

High temperature coating高溫涂層

Hose support軟管支架

Hub assembly轂組件

Hub bearing車輪輪轂軸承

Hydraulic device液壓裝置

Hydraulic engine液壓發動機

Hydrostatic strength流體靜力強度

IMC(In-Mold Coating)模具內部涂層

Immersion paint浸漆

Immersion test浸漬試驗，浸泡試驗

Immovable support固定刀架

Impact analysis碰撞試驗撞擊分析

Impact bending沖擊撓曲

Impact specimen沖擊試樣

Impregnate浸漬

Impelling strength沖擊韌性

Injection head注射頭

Injection-moulded composites注射模塑復合材料

Injection moulded part注塑制件

Injection nozzle注射噴口，壓注噴口

Intermittent entry間歇供給，不連續供給

Intermittent failure間接性故障

Izod test懸臂沖擊試驗

Jack千斤頂，起重器；傳動裝置

Jack engine輔助發動機

Jackbit insert切刀，刀具，刃口

Jacket護套，套管，保護罩，蒙皮

Jar-proof防震的

Jaw鉗口；定位銷

Jell膠凝，凝固，固結

Jet milling噴射研磨

Jig夾具，定位模具

Jig-adjusted粗調的

Job program工作程序

Joining nipple接合螺管

Joining on butt對頭接合

Joint face of a pattern分模面

Joint gate分型面內澆口

Joint packing填充墊圈，接合填密

Joint sealing material填縫料

Joint-shaped support鉸接支架

Joint strength連接強度

Jump welded tube對縫焊管，焊接管

Junction bolt接合螺栓

Junction point接點

Keeping life保存期，產品有效期

Kenel型芯

Ketene乙烯酮, 烯酮

Ketene dimethyl二甲酮

Ketimide酰基酮亞胺

Ketimine酮亞胺

Ketoamine酮胺，氨基酮

Ketol乙酮醇

Ketone甲酮

Keying strength咬合強度

Knife holder刀具，刀架

Knockout脫模

Knockout pin脫模銷

Knockout plate脫模板

Knoop scale努氏硬度標度

Knuckle joint鉸鏈連接

Koplon高濕模量粘膠纖維

Koroseal氯乙烯樹脂

Lacquer揮發性漆；涂漆

Lacquer finish噴漆，上漆，罩光

Lacquer formation漆膜形成，成漆

Lacquer putty膩?zhàn)樱嬗糜突?/P>

Lacquering 上清漆

Laminate construction thickness結構層厚度

Laminated panel薄層狀板

Laminated plastics層壓塑料制品, 塑料層板

Laminated thermosetting plastics層壓熱固塑料

Latex paints 清漆

Lay-up(塑料，夾板的)鋪疊成型

Light-alloy body part輕合金車身零件

Lining 襯里，襯墊

Loaded haul cycle載貨行程

Location bearing定位軸承

Location guide固定導桿，定位導桿

Location hole定位孔

Location tolerance位置公差, 安裝公差

Location pin定位銷

Lock bolt鎖緊螺釘

Low pressure injection moulding低壓模塑成型

Low shrink resin低收縮樹脂

Luggage rack行李架

Machining accuracy加工精度

Machining center加工中心

Main shaft gear bushing主軸齒輪襯套

Mandrel 卷芯，模芯；芯軸

Manifold hood歧管外罩

Manual Lay-Up人工手糊

Manual spray-up手工噴射

Manual truck手推車

Manufacturing drawing制造圖紙

Matched molds合模

Matrix 基體，基質

Mechanical properties機械性能

Metal bonding金屬粘結

Metal-working machine金屬加工機床

Methanol甲醇

Mismachining tolerance加工誤差

Modular組裝式的

Modulus of elasticity彈性模量

Mould operation模具操作

Moulded plastics模壓塑料

Moulding嵌條；成型；裝飾件

Mount support裝配支架

Multi-axial stress多軸向應力

Multi-tool machining多刀切削加工

 

Needled mat針刺氈，針織氈

Non-ductile fracture無塑性破壞

Nontwisting fiber不加捻纖維

Notched izod test帶缺口懸臂梁式?jīng)_擊試驗

Nozzle管嘴，噴嘴

Numerically controlled engine lathe數控普通車床

Nylon resin尼龍樹脂

OEM (Original Equipment Manufacturer) 原始設備生產商

Offset cab側置駕駛室

On-site forming現場發泡

On-site winding現場纏繞成型

Open molding敞開式模塑法

Opening mould開模

Optimized design優化設計

Orifice注孔

Orthophenyl tolyl ketone鄰苯基甲苯基酮

Orthophthalic resin ortho鄰苯二甲酸樹脂

Osmotic pressure滲透壓力

Outboard wing外翼

Outer panel skin蒙皮

Oven heating烘箱加熱，加熱固化

Over-engineering過份設計的

Over flow溢流

Over-spray過噴

Overhead traveling crane高空移動行車

Overhead-valve engine頂置氣門發動機

Overhung trailer外伸式拖車

Oxide paint氧化物涂料

Package power動力裝置總成

Packed 緊密的，密實的；有密封的，有填料的

Packing襯墊；填料，密封填料；包裝

PAD(Paint As Required)按需涂漆

Paint base coat上底漆

Paint blemish涂漆缺陷

Paint blower噴漆用壓力機，噴漆槍

Paint brush涂漆刷

Paint dilution油漆稀釋

PE(Polyethylene)聚乙烯

Pedestal mounted落地安裝的

Phenolic plastic酚醛塑料

Phenyl ketone苯基甲酮

Pit mounted嵌入式安裝

Pivotal arm樞軸

Plastic structural component塑料結構零部件

Plastic upholstery(座椅)塑料蒙面

Play compensation間隙補償

PLC(Programmable Logical Controller) 可編程序邏輯控制器

Polycarbonate plastics聚碳酸脂塑料

Polyester resin聚脂樹脂

Polyimide聚酰亞胺

Polymer聚合物，高分子，多聚體

Polyurethane foam聚氨酯泡沫塑料

Polyvinyl聚乙烯的, 聚乙烯

Polyvinyl fluoride聚氟乙烯

Prefabricated parts成品零部件，制造好的零部件

Propylene resin丙烯類樹脂

Protecting lacquer防護漆

PSF(Polystyrene Foam)聚苯乙烯泡沫塑料

PTFE(Polytetrafluoroethylene)聚四氟乙烯

Pultrusion拉擠成型

Putty knife油灰（膩?zhàn)樱┕午P

QC(Quality Control)質量控制

QCS(Quality Control Standard)質量管理控制標準

QR(Quality Requirements)質量規格(要求)

Quality certification質量認證

Quantity production大量（成批）生產，大規模生產

Quantity production大量（成批）生產，大規模生產

Quarter panel brace后側圍板支撐件

Quarter panel lower extension后側圍板下延伸部

Quarter trim cap后側圍裝飾板蓋

Quarte wheel house后側圍輪滾罩，后側圍車輪室

Quasi-isotropic laminate準各向同性層板

Quench淬火

Rack truck架子車, 移動架

Radial dispersion徑向位移

Radial loading徑向力(載荷)

Radial pump徑向離心泵

Radiation protective paint防輻射涂料

Radiator散熱器

Rag毛刺

RARTM(Rubber-assisted RTM)橡膠輔助RTM(用橡膠取代芯材的熱膨脹RTM)

Reactive resin活性樹脂, 反應型樹脂

Rear skirt rail后圍裙邊梁

Reciprocating engine活塞式發動機, 往復式發動機

Reinforcement車身加強件，增強材料；構架

Repeat accuracy重復精確度

Repeatability設備重復定位精度

Resin formulation樹脂配方

Retaining nest定位槽

Return trip回程，返回行程

Rib筋，加強筋

RIFT(Resin Infusion Under Flexible Tooling)撓性上模具樹脂浸漬工藝

RIM(Reaction Injection Molding)反應注射模塑

Safety hood安全罩

Sample testing樣品試驗

Sand wet(車身/涂裝)濕砂打磨

Sandwich body夾層結構車身

Sandwich construction夾層結構

Sandwich panel多層板，復合板

Shaft assembly軸組件

Skin coat表層；罩面層

Solvent reclaim溶劑的回收

Stiffener加強件

Storage modulus儲能模量

Stress at definite elongation定伸應力

Stretched acetylic plastic拉伸丙烯酸塑料

String milling連續銑削

Stroke(懸架)減振器，沖程

Structural instrument panel結構儀表板

Structural layer結構層

Styrene苯乙烯

Styrofoam聚苯乙烯泡沫塑料

Surface mat表面薄氈

Synthetic resin paint合成樹脂涂料

Tack strength粘著強度

Tail gate(卡車等的)后擋板

Teflon聚四氟乙烯(塑料, 絕緣材料)

TERTM(Thermal-Expansion Resin Transfer Molding)熱膨脹樹脂傳遞模塑

Thermoplastic plastics熱塑性塑料

Thermoset resin熱固性樹脂

Thickening agent增粘劑

Trim waste內飾廢料

Trimming orientation修邊定位

Turbulent heating湍流加熱

Turndown ratio衰減比率

Twisting stress扭脅強, 扭應力

U bolt U形螺栓

U bolt plateU 形螺栓墊板

Ultimate mechanical strength極限機械強度

Ultraviolent sensitive coating紫外線感光涂層

Undercoat paint頭道漆

Uniaxial drawing單軸拉伸

Unsaturated polyester resin非飽和聚酯樹脂

Unyielding support不可壓縮支架, 剛性支架

Upper yield stress上屈服應力

Urethane coating氨基甲酸乙酯涂層

UVRTM(Ultra-violet RTM)紫外線固化RTM（利用紫外線進行固化）

VA RTM (Vacuum Assisted Resin Transfer Molding) 真空輔助RTM

Vacuum bag molding真空袋模制法

VARI(Vacuum Assisted Resin injection)真空輔助樹脂注射

Variable speed無級變速

Ventilation duct通風管

Ventilator(Ventilating equipment)通風裝置

Vibratory stress振動應力

Wing truss grid翼子（擋泥）板加強件

Winding纏繞

Wingtip assembly翼尖整流罩

Wire drawing拉絲

Wiring press卷邊壓力機, 嵌線卷邊機

Workpiece grippe工件夾子（持器），機械手

Woven roving fabric（玻璃纖維）無捻粗紗布織物

Xylenol Carboxylic Acid二甲苯酚酸

Xlylene亞二甲苯基

Xyster刮刀

X alloy銅鋁合金

Xenidium膠合板

Xenidium膠合板

Xylene 二甲苯

Xylene resin二甲苯樹脂

Yard-crane移動吊車，場內移動起重機

Yarn count紗線支數，絲線支數

Yarn strength紗線強度，長絲強度

Yield limit屈服極限，屈服點

Yield point under bending stress彎曲應力下的屈服點

Yield stress屈服應力, 屈服點

Yield stress controlled bonding屈服應力粘結

Zedeflon四氟乙烯均聚物

Zero checker定零位裝置, 零位校驗

Zero clearance零間隙

Zero compensation零位補償

Zero initial condition零初始條件

Zero setting(儀表)零位調整, 置零

Zero shrinkage resin零收縮樹脂

Zone control區域控制

VIMP (Variable Infusion Molding Process)可變浸漬模塑

Vinyl chloride resin聚氯乙烯樹脂

VOC(Volatile Organic Compound)揮發性有機化合物

Volume modulus體積模數

Vortex generator(車身)擾流器，導流板

VRV(Vacuum Reducer Valve)真空減壓閥

Warping stress翹曲應力

Water tolerance耐水性

Wedge gripping楔形夾具

Wheel fender翼子板

Waste utilization廢物利用，廢物處理

Water shield防水罩，擋泥板；密封條